ROPE LIGHT > LED > BULK 150 FT. REELS > 1/2" DIAMETER > 120V
|
|
Description: Consists of an inner clear PVC extrusion, enclosing a series/parallel array of LEDs (Light Emitting Diodes), encased in an outer layer of clear PVC tubing that creates a neon effect when powered. Produces approximately 70% of the light output of glass neon. Developed to be resistant to impact, water, UV rays and extreme temperatures and still remain flexible and strong enough to bend into severe angles without breakage. Know generically as ":LED Rope Light". Each full 150 Ft. Reel is UL Listed, however, any alteration of the Rope, Power Cord, Power Connector or End Cap via cutting or splicing voids the UL Listing. The additional Connector Kits (Power Cord with Molded 1.6A In-Line AC to DC Inverter, Compression Type Power Connector and Slip-On End Cap) provided with the Reel are not safety rated.
SPECIFICATIONS
|
SAFETY LISTING
INPUT VOLTAGE: CIRCUITS: DIAMETER: FLEXIBILITY: UV-RESISTANT WATER-RESISTANT LEDs LED RATED LIFE LED SPACING LED COLORS TUBING COLOR ROPE LENGTH CUTTING INCREMENTS DIMMING ABILITY |
UL Listed as Suitable for Wet Locations. Note: Any alteration of the 150 Ft. Reel of Rope and its' Power Cord, Power Connector or End Cap voids the UL Listing.
120VAC / 60Hz. 1-Circuit (2-Wire) Steady Burn. 1/2" (13mm). A strain relief system allows severe angle mounting. UV Stabilizers are blended into the PVC Tubing. The PVC Tubing is impervious to water and suitable for outdoor use. 3mm LEDs (Light Emitting Diodes) mounted vertically. 60,000 Hours. 1-inch. Ultra Warm White (2100K), Cool White (6400K), Amber, Blue, Green, Red, Yellow. Clear. 150 Ft. Bulk Reel. Every 3 Ft. for: Ultra Warm White (2100K), Cool White (6400K), Blue and Green. Every 5 Ft. for: Amber, Red and Yellow. Dimmable with most electronic low voltage and LED/CFL Dimmers (Minimum loads may apply.). |
|
ACCESSORIES
|
Connector Kit (DL-LED-120V-146):
- Consists of 3 Parts: 5 Ft. White Cord with Fused 2-Prong Plug and 1.6A AC to DC Molded In-Line Inverter; a Compression Fit Power Connector that attaches the Power Cord to the Rope; a Slip Fit End Cap. - Voltage Input: 120VAC / 60Hz. 
Invisible Splice (DL-2W-7):
- Connector to add on, or replace a section of, 2-Wire 1/2" Diameter Rope Light. Often used in conjunction with the DL-ST-3 (below) Shrink Tube. - Will fit into DL-CH-4 Mounting Channel. - Clear Plastic.
Regular Splice (DL-2W-3):
- Connector to add on, or replace a section of, 2-Wire 1/2" Diameter Rope Light. - Compression fitting on both sides of device. - White Plastic.
Y-Connector (DL-2W-Y):
T-Connector (DL-2W-T):
- Each leg of the "T" only accepts 2-Wire 1/2" Diameter Rope Light. (This Device does not accept a Power Cord or Power Connector directly. A length of Rope Light would have to be connected between the "T" and the Power Connector / Power Cord. 
Mounting Channel (DL-CH-4):
- Clear Plastic. - Flat Back with U-Channel Profile. - 4 Ft. Length. Easily cut to length with hack saw. 
Mounting Clip with Screw (DL-5):
- Clear Plastic. - U-Clip sits on Flat Back Tab that has 2 holes to accept provided screw. |
|
Shrink Tube (DL-ST-3):
- 3 inch Length to shrink over an Invisible Splice (above) connection. - Clear. |
ORDER CODES
|
TYPE / DIAMETER
-------------------------- DL-LED = 1/2" Diameter
LED Rope Light |
VOLTAGE
120V = 120VAC / 60Hz
|
LED COLOR
UWW = 2100K Ultra Warm White
CW = 6400K Cool White GR = Green BL = Blue AM = Amber RE = Red YE = Yellow |
LENGTH
150 = 150 Ft. Reel
|
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
ORDER CODE EXAMPLE: DL-LED-120V-CW-150
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
